View K4D261638F-TC33_71327.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

K4D261638F
128M GDDR SDRAM
128Mbit GDDR SDRAM
2M x 16Bit x 4 Banks Graphic Double Data Rate Synchronous DRAM
Revision 1.2 January 2004
Samsung Electronics reserves the right to change products or specification without notice.
-1-
Rev. 1.2 (Jan. 2004)
K4D261638F
Revision History
Revision 1.2 (January 30, 2004)
* Changed tWR & tWR_A of K4D261638F-TC25/2A/33/36 from 3tCK to 4tCK * Changed tRC of K4D261638F-TC25 from 17tCK to 18tCK * Changed tRC of K4D261638F-TC2A/33/36 from 15tCK to 16tCK * Changed tRAS of K4D261638F-TC25 from 12tCK to 13tCK. * Changed tRAS of K4D261638F-TC2A/33/36 from 10tCK to 11tCK. * Changed tDAL of K4D261638F-TC25/2A/33/36 from 8tCK to 9tCK
128M GDDR SDRAM
Revision 1.1 (January 7, 2004)
* Added K4D261638F-TC25 in the spec.
Revision 1.0 (December 5, 2003) Revision 0.9 (October 14, 2003) - Preliminary Spec
* Defined DC spec
Revision 0.1 (October 2, 2003) - Target Spec
* Added Lead free package part number in the datasheet
Revision 0.0 (August 6, 2003) - Target Spec
* Defined Target Specification
-2-
Rev. 1.2 (Jan. 2004)
K4D261638F
128M GDDR SDRAM
2M x 16Bit x 4 Banks Graphic Double Data Rate Synchronous DRAM with Bi-directional Data Strobe and DLL FEATURES
* 2.5V + 5% power supply for device operation * 2.5V + 5% power supply for I/O interface * SSTL_2 compatible inputs/outputs * 4 banks operation * MRS cycle with address key programs -. Read latency 3, 4 and 5(clock) -. Burst length (2, 4 and 8) -. Burst type (sequential & interleave) * All inputs except data & DM are sampled at the positive going edge of the system clock * Differential clock input * No Wrtie-Interrupted by Read Function * 2 DQS's ( 1DQS / Byte ) * Data I/O transactions on both edges of Data strobe * DLL aligns DQ and DQS transitions with Clock transition * Edge aligned data & data strobe output * Center aligned data & data strobe input * DM for write masking only * Auto & Self refresh * 32ms refresh period (4K cycle) * 66pin TSOP-II * Maximum clock frequency up to 400MHz * Maximum data rate up to 800Mbps/pin
ORDERING INFORMATION
Part NO. K4D261638F-TC25 K4D261638F-TC2A K4D261638F-TC33 K4D261638F-TC36 K4D261638F-TC40 K4D261638F-TC50 Max Freq. 400MHz 350MHz 300MHz 275MHz 250MHz 200MHz Max Data Rate 800Mbps/pin 700Mbps/pin 600Mbps/pin 550Mbps/pin 500Mbps/pin 400Mbps/pin SSTL_2 66pin TSOP-II Interface Package
K4D261638F-LC is the Lead Free package part number. For the K4D261638F-TC25/2A, VDD & VDDQ = 2.8V+0.1V
GENERAL DESCRIPTION
FOR 2M x 16Bit x 4 Bank DDR SDRAM
The K4D261638F is 134,217,728 bits of hyper synchronous data rate Dynamic RAM organized as 4 x 2,097,152 words by 16 bits, fabricated with SAMSUNG's high performance CMOS technology. Synchronous features with Data Strobe allow extremely high performance up to 1.6GB/s/chip. I/O transactions are possible on both edges of the clock cycle. Range of operating frequencies, programmable burst length and programmable latencies allow the device to be useful for a variety of high performance memory system applications.
-3-
Rev. 1.2 (Jan. 2004)
K4D261638F
PIN CONFIGURATION (Top View)
VDD DQ0 VDDQ DQ1 DQ2 VSSQ DQ3 DQ4 VDDQ DQ5 DQ6 VSSQ DQ7 NC VDDQ LDQS NC VDD NC LDM WE CAS RAS CS NC BA0 BA1 AP/A10 A0 A1 A2 A3 VDD 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 66 65 64 63 62 61 60 59 58 VSS DQ15 VSSQ DQ14 DQ13 VDDQ DQ12 DQ11 VSSQ DQ10 DQ9 VDDQ DQ8 NC VSSQ UDQS NC VREF VSS UDM CK CK CKE NC NC A11 A9 A8 A7 A6 A5 A4 VSS
128M GDDR SDRAM
66 PIN TSOP(II) (400mil x 875mil) (0.65 mm Pin Pitch)
57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34
PIN DESCRIPTION
CK,CK CKE CS RAS CAS WE L(U)DQS L(U)DM RFU Differential Clock Input Clock Enable Chip Select Row Address Strobe Column Address Strobe Write Enable Data Strobe Data Mask Reserved for Future Use BA0, BA1 A0 ~A11 DQ0 ~ DQ15 VDD VSS VDDQ VSSQ NC Bank Select Address Address Input Data Input/Output Power Ground Power for DQ's Ground for DQ's No Connection
-4-
Rev. 1.2 (Jan. 2004)
K4D261638F
INPUT/OUTPUT FUNCTIONAL DESCRIPTION
Symbol CK, CK*1 Input Type
128M GDDR SDRAM
Function The differential system clock Input. All of the inputs are sampled on the rising edge of the clock except DQ's and DM's that are sampled on both edges of the DQS. Activates the CK signal when high and deactivates the CK signal when low. By deactivating the clock, CKE low indicates the Power down mode or Self refresh mode. CS enables the command decoder when low and disabled the command decoder when high. When the command decoder is disabled, new commands are ignored but previous operations continue. Latches row addresses on the positive going edge of the CK with RAS low. Enables row access & precharge. Latches column addresses on the positive going edge of the CK with CAS low. Enables column access. Enables write operation and row precharge. Latches data in starting from CAS, WE active. Data input and output are synchronized with both edge of DQS. For the x16, LDQS corresponds to the data on DQ0-DQ7 ; UDQS corresponds to the data on DQ8-DQ15. Data in Mask. Data In is masked by DM Latency=0 when DM is high in burst write. For the x16, LDM corresponds to the data on DQ0-DQ7 ; UDM correspons to the data on DQ8-DQ15. Data inputs/Outputs are multiplexed on the same pins. Selects which bank is to be active. Row/Column addresses are multiplexed on the same pins. Row addresses : RA0 ~ RA11, Column addresses : CA0 ~ CA8. Power and ground for the input buffers and core logic. Isolated power supply and ground for the output buffers to provide improved noise immunity. Reference voltage for inputs, used for SSTL interface. This pin is recommended to be left "No connection" on the device
CKE
Input
CS
Input
RAS CAS WE
Input Input Input
LDQS,UDQS
Input/Output
LDM,UDM DQ0 ~ DQ15 BA0, BA1 A0 ~ A11 VDD/VSS VDDQ/VSSQ VREF NC/RFU
Input Input/Output Input Input Power Supply Power Supply Power Supply No connection/ Reserved for future use
*1 : The timing reference point for the differential clocking is the cross point of CK and CK. For any applications using the single ended clocking, apply VREF to CK pin.
-5-
Rev. 1.2 (Jan. 2004)
K4D261638F
BLOCK DIAGRAM (2Mbit x 16I/O x 4 Bank)
128M GDDR SDRAM
16
Intput Buffer I/O Control LWE LDMi
CK, CK Bank Select
Data Input Register Serial to parallel
2Mx16 Output Buffer 2-bit prefetch Sense AMP Refresh Counter Row Buffer Row Decoder 2Mx16 2Mx16 2Mx16
32 16
x16
DQi
Address Register
CK,CK ADDR
Column Decoder LCBR LRAS Col. Buffer
Latency & Burst Length Strobe Gen. Data Strobe
Programming Register LCKE LRAS LCBR LWE LCAS LWCBR
DLL
CK,CK
LDMi
Timing Register
CK,CK
CKE
CS
RAS
CAS
WE
LDM
UDM
-6-
Rev. 1.2 (Jan. 2004)
K4D261638F
FUNCTIONAL DESCRIPTION
* Power-Up Sequence
128M GDDR SDRAM
DDR SDRAMs must be powered up and initialized in a predefined manner to prevent undefined operations. 1. Apply power and keep CKE at low state (All other inputs may be undefined) - Apply VDD before VDDQ . - Apply VDDQ before VREF & VTT 2. Start clock and maintain stable condition for minimum 200us. 3. The minimum of 200us after stable power and clock(CK,CK ), apply NOP and take CKE to be high . 4. Issue precharge command for all banks of the device. 5. Issue a EMRS command to enable DLL *1 6. Issue a MRS command to reset DLL. The additional 200 clock cycles are required to lock the DLL. *1,2 7. Issue precharge command for all banks of the device. 8. Issue at least 2 or more auto-refresh commands. 9. Issue a mode register set command with A8 to low to initialize the mode register. *1 The additional 200cycles of clock input is required to lock the DLL after enabling DLL. *2 Sequence of 6&7 is regardless of the order.
Power up & Initialization Sequence
0 CK,CK 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
~
~~
Command
precharge ALL Banks
EMRS
MRS DLL Reset
precharge ALL Banks
1st Auto Refresh
2nd Auto Refresh
~~
tRP
2 Clock min.
2 Clock min.
tRP
tRFC
tRFC
~
2 Clock min.
Mode
Register Set
Any Command
~
Inputs must be stable for 200us
* When the operating frequency is changed, DLL reset should be required again. After DLL reset again, the minimum 200 cycles of clock input is needed to lock the DLL.
~
200 Clock min.
-7-
Rev. 1.2 (Jan. 2004)
K4D261638F
MODE REGISTER SET(MRS)
128M GDDR SDRAM
The mode register stores the data for controlling the various operating modes of DDR SDRAM. It programs CAS latency, addressing mode, burst length, test mode, DLL reset and various vendor specific options to make DDR SDRAM useful for variety of different applications. The default value of the mode register is not defined, therefore the mode register must be written after EMRS setting for proper operation. The mode register is written by asserting low on CS, RAS, CAS and WE(The DDR SDRAM should be in active mode with CKE already high prior to writing into the mode register). The state of address pins A0 ~ A11 and BA0, BA1 in the same cycle as CS, RAS, CAS and WE going low is written in the mode register. Minimum two clock cycles are requested to complete the write operation in the mode register. The mode register contents can be changed using the same command and clock cycle requirements during operation as long as all banks are in the idle state. The mode register is divided into various fields depending on functionality. The burst length uses A0 ~ A2, addressing mode uses A3, CAS latency(read latency from column address) uses A4 ~ A6. A7 is used for test mode. A8 is used for DLL reset. A7,A8, BA0 and BA1 must be set to low for normal MRS operation. Refer to the table for specific codes for various burst length, addressing modes and CAS latencies. BA1 BA0 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 Address Bus
RFU
0
RFU
DLL
TM
CAS Latency
BT
Burst Length
Mode Register
DLL A8 0 1 DLL Reset No Yes
Test Mode A7 0 1 mode Normal Test
Burst Type A3 0 1 Type Sequential Interleave Burst Length
CAS Latency BA0 0 1 An ~ A0 MRS EMRS A6 0 0 0 0 * RFU(Reserved for future use) should stay "0" during MRS cycle. 1 1 1 1 MRS Cycle
0 CK, CK Command
NOP Precharge All Banks NOP NOP MRS
A2 Latency Reserved Reserved Reserved 3 4 5 Reserved Reserved 0 0 0 0 1 1 1 1
A1 0 0 1 1 0 0 1 1
A0 0 1 0 1 0 1 0 1
Burst Type Sequential Reserve 2 4 8 Reserve Reserve Reserve Reserve Interleave Reserve 2 4 8 Reserve Reserve Reserve Reserve
A5 0 0 1 1 0 0 1 1
A4 0 1 0 1 0 1 0 1
1
2
3
4
5
6
7
8
NOP
Any Command
NOP
NOP
tRP
tMRD=2 tCK
*1 : MRS can be issued only at all banks precharge state. *2 : Minimum tRP is required to issue MRS command. -8-
Rev. 1.2 (Jan. 2004)
K4D261638F
EXTENDED MODE REGISTER SET(EMRS)
128M GDDR SDRAM
The extended mode register stores the data for enabling or disabling DLL and selecting output driver strength. The default value of the extended mode register is not defined, therefore the extened mode register must be written after power up for enabling or disabling DLL. The extended mode register is written by asserting low on CS, RAS, CAS, WE and high on BA0(The DDR SDRAM should be in all bank precharge with CKE already high prior to writing into the extended mode register). The state of address pins A0, A2 ~ A5, A7 ~ A11 and BA1 in the same cycle as CS, RAS, CAS and WE going low are written in the extended mode register. A1 and A6 are used for setting driver strength to normal, weak or matched impedance. Two clock cycles are required to complete the write operation in the extended mode register. The mode register contents can be changed using the same command and clock cycle requirements during operation as long as all banks are in the idle state. A0 is used for DLL enable or disable. "High" on BA0 is used for EMRS. All the other address pins except A0,A1,A6 and BA0 must be set to low for proper EMRS operation. Refer to the table for specific codes.
BA1 BA0 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
Address Bus Extended Mode Register
RFU
1
RFU
D.I.C
RFU
D.I.C
DLL
BA0 0 1
An ~ A0 MRS EMRS
A6 0 1
A1 1 1
Output Driver Impedence Control Weak Matched
A0 0 1
DLL Enable Enable Disable
*1 : RFU(Reserved for future use) should stay "0" during EMRS cycle.
-9-
Rev. 1.2 (Jan. 2004)
K4D261638F
ABSOLUTE MAXIMUM RATINGS
Parameter Voltage on any pin relative to Vss Voltage on VDD supply relative to Vss Voltage on VDD supply relative to Vss Storage temperature Power dissipation Short circuit current Symbol VIN, VOUT VDD VDDQ TSTG PD IOS
128M GDDR SDRAM
Value -0.5 ~ 3.6 -1.0 ~ 3.6 -0.5 ~ 3.6 -55 ~ +150 2.0 50
Unit V V V C W mA
Note : Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded. Functional operation should be restricted to recommended operating condition. Exposure to higher than recommended voltage for extended periods of time could affect device reliability.
POWER & DC OPERATING CONDITIONS(SSTL_2 In/Out)
Recommended operating conditions(Voltage referenced to VSS=0V, TA=0 to 65C)
Parameter
Device Supply voltage Output Supply voltage Reference voltage Termination voltage Input logic high voltage Input logic low voltage Output logic high voltage Output logic low voltage Input leakage current Output leakage current
Symbol
VDD VDDQ VREF Vtt VIH(DC) VIL(DC) VOH VOL IIL IOL
Min
2.375 2.375 0.49*VDDQ VREF-0.04 VREF+0.15 -0.30 Vtt+0.76 -5 -5
Typ
2.50 2.50 VREF -
Max
2.625 2.625 0.51*VDDQ VREF+0.04 VDDQ+0.30 VREF-0.15 Vtt-0.76 5 5
Unit
V V V V V V V V uA uA
Note
1, 7 1, 7 2 3 4 5 IOH=-15.2mA IOL=+15.2mA 6 6
Note : 1. Under all conditions VDDQ must be less than or equal to VDD. 2. VREF is expected to equal 0.50*VDDQ of the transmitting device and to track variations in the DC level of the same. Peak to peak noise on the VREF may not exceed + 2% of the DC value. Thus, from 0.50*VDDQ, VREF is allowed + 25mV for DC error and an additional + 25mV for AC noise. 3. Vtt of the transmitting device must track VREF of the receiving device. 4. VIH(max.)= VDDQ +1.5V for a pulse width and it can not be greater than 1/3 of the cycle rate. 5. VIL(mim.)= -1.5V for a pulse width and it can not be greater than 1/3 of the cycle rate. 6. For any pin under test input of 0V < VIN < VDD is acceptable. For all other pins that are not under test VIN=0V. 7. For the K4D261638F-TC25/2A, VDD & VDDQ = 2.8V+0.1V
- 10 -
Rev. 1.2 (Jan. 2004)
K4D261638F
DC CHARACTERISTICS
Recommended operating conditions Unless Otherwise Noted, TA=0 to 65C)
128M GDDR SDRAM
Version Parameter Operating Current (One Bank Active) Precharge Standby Current in Power-down mode Precharge Standby Current in Non Power-down mode Active Standby Current power-down mode Active Standby Current in in Non Power-down mode Operating Current ( Burst Mode) Refresh Current Self Refresh Current Symbol Test Condition -25 ICC1 ICC2P ICC2N ICC3P ICC3N ICC4 ICC5 ICC6 Burst Lenth=2 tRC tRC(min) -2A 210 60 90 75 135 400 245 75 65 100 290 210 4 70 60 100 275 200 -33 190 -36 180 45 65 55 95 260 195 60 50 90 245 190 -40 170 -50 150 mA mA mA mA mA mA mA mA 2 1 Unit Note
IOL=0mA, tCC= tCC(min)
CKE VIL(max), tCC= tCC(min) CKE VIH(min), CS VIH(min),
TBD TBD TBD TBD TBD TBD TBD
tCC= tCC(min)
CKE VIL(max), tCC= tCC(min) CKE VIH(min), CS VIH(min),
tCC= tCC(min) tRC tRFC(min)tRC tRFC(min) Page Burst, All Banks activated. tRC tRFC(min)
CKE 0.2V
Note : 1. Measured with outputs open. 2. Refresh period is 32ms.
AC INPUT OPERATING CONDITIONS
Recommended operating conditions(Voltage referenced to VSS=0V, VDD=2.5V+ 5%, VDDQ=2.5V+ 5%,TA=0 to 65C)
Parameter
Input High (Logic 1) Voltage; DQ Input Low (Logic 0) Voltage; DQ Clock Input Differential Voltage; CK and CK Clock Input Crossing Point Voltage; CK and CK
Symbol
VIH VIL VID VIX
Min
VREF+0.35 0.7 0.5*VDDQ-0.2
Typ
-
Max
VREF-0.35 VDDQ+0.6 0.5*VDDQ+0.2
Unit
V V V V
Note
1 2
Note : 1. VID is the magnitude of the difference between the input level on CK and the input level on CK 2. The value of VIX is expected to equal 0.5*VDDQ of the transmitting device and must track variations in the DC level of the same 3. For the K4D261638F-TC25/2A, VDD & VDDQ = 2.8V+0.1V.
- 11 -
Rev. 1.2 (Jan. 2004)
K4D261638F
AC OPERATING TEST CONDITIONS (VDD=2.5V5%, TA= 0 to 65C)
Parameter Input reference voltage for CK(for single ended) CK and CK signal maximum peak swing CK signal minimum slew rate Input Levels(VIH/VIL) Input timing measurement reference level Output timing measurement reference level Output load condition
1.For the K4D261638F-TC25/2A, VDD & VDDQ = 2.8V+0.1V.
128M GDDR SDRAM
Value 0.50*VDDQ 1.5 1.0 VREF+0.35/VREF-0.35 VREF Vtt See Fig.1
Unit V V V/ns V V V
Note
Vtt=0.5*VDDQ
RT=50 Output Z0=50
VREF =0.5*VDDQ
CLOAD=30pF
(Fig. 1) Output Load Circuit
CAPACITANCE (VDD=2.5V, TA= 25C, f=1MHz)
Parameter
Input capacitance( CK, CK ) Input capacitance(A0~A11, BA0~BA1) Input capacitance ( CKE, CS, RAS,CAS, WE ) Data & DQS input/output capacitance(DQ0~DQ15) Input capacitance(DM0 ~ DM3)
Symbol
CIN1 CIN2 CIN3 COUT CIN4
Min
1.0 1.0 1.0 1.0 1.0
Max
5.0 4.0 4.0 6.5 6.5
Unit
pF pF pF pF pF
DECOUPLING CAPACITANCE GUIDE LINE
Recommended decoupling capacitance added to power line at board. Parameter Decoupling Capacitance between VDD and VSS Decoupling Capacitance between VDDQ and VSSQ Symbol CDC1 CDC2 Value 0.1 + 0.01 0.1 + 0.01 Unit uF uF
Note : 1. VDD and VDDQ pins are separated each other. All VDD pins are connected in chip. All VDDQ pins are connected in chip. 2. VSS and VSSQ pins are separated each other All VSS pins are connected in chip. All VSSQ pins are connected in chip.
- 12 -
Rev. 1.2 (Jan. 2004)
K4D261638F
AC CHARACTERISTICS - 1
Parameter
CK cycle time CK high level width CK low level width DQS out access time from CK Output access time from CK Data strobe edge to Dout edge Read preamble Read postamble CK to valid DQS-in DQS-In setup time DQS-in hold time DQS write postamble DQS-In high level width DQS-In low level width Address and Control input setup Address and Control input hold DQ and DM setup time to DQS DQ and DM hold time to DQS Clock half period Data output hold time from DQS CL=3 CL=4 CL=5
128M GDDR SDRAM
Symbol
-25 Min
2.5 0.45 0.45 -0.55 -0.55 0.9 0.4 0.85 0 0.35 0.4 0.45 0.45 0.8 0.8 0.35 0.35 tCLmin or tCHmin tHP-0.4
-2A Max
4 0.55 0.55 0.55 0.55 0.35 1.1 0.6 1.15 0.6 0.55 0.55 -
-33 Max
10 0.55 0.55 0.6 0.6 0.35 1.1 0.6 1.15 0.6 0.6 0.6 -
Min
2.86 0.45 0.45 -0.6 -0.6 0.9 0.4 0.85 0 0.35 0.4 0.4 0.4 0.9 0.9 0.35 0.35 tCLmin or tCHmin tHP-0.35
Min
3.3 0.45 0.45 -0.6 -0.6 0.9 0.4 0.85 0 0.35 0.4 0.4 0.4 0.9 0.9 0.35 0.35 tCLmin or tCHmin tHP-0.35
Max
10 0.55 0.55 0.6 0.6 0.35 1.1 0.6 1.15 0.6 0.6 0.6 -
Unit
ns ns ns tCK tCK ns ns ns tCK tCK tCK ns tCK tCK tCK tCK ns ns ns ns ns ns
Note
tCK tCH tCL tDQSCK tAC tDQSQ tRPRE tRPST tDQSS tWPRES tWPREH tWPST tDQSH tDQSL tIS tIH tDS tDH tHP tQH
1
1 1
Note 1 : - The JEDEC DDR specification currently defines the output data valid window(tDV) as the time period when the data strobe and all data associated with that data strobe are coincidentally valid. - The previously used definition of tDV(=0.35tCK) artificially penalizes system timing budgets by assuming the worst case output vaild window even then the clock duty cycle applied to the device is better than 45/55% - A new AC timing term, tQH which stands for data output hold time from DQS is difined to account for clock duty cycle variation and replaces tDV - tQHmin = tHP-X where . tHP=Minimum half clock period for any given cycle and is defined by clock high or clock low time(tCH,tCL) . X=A frequency dependent timing allowance account for tDQSQmax
- 13 -
Rev. 1.2 (Jan. 2004)
K4D261638F
AC CHARACTERISTICS - 2
Parameter
CK cycle time CK high level width CK low level width DQS out access time from CK Output access time from CK Data strobe edge to Dout edge Read preamble Read postamble CK to valid DQS-in DQS-In setup time DQS-in hold time DQS write postamble DQS-In high level width DQS-In low level width Address and Control input setup Address and Control input hold DQ and DM setup time to DQS DQ and DM hold time to DQS Clock half period Data output hold time from DQS CL=3 CL=4 CL=5
128M GDDR SDRAM
Symbol
-36 Min
3.6 0.45 0.45 -0.6 -0.6 0.9 0.4 0.85 0 0.35 0.4 0.4 0.4 0.9 0.9 0.40 0.40 tCLmin or tCHmin tHP-0.4
-40 Max
10 0.55 0.55 0.6 0.6 0.40 1.1 0.6 1.15 0.6 0.6 0.6 -
-50 Max
10 0.55 0.55 0.6 0.6 0.4 1.1 0.6 1.15 0.6 0.6 0.6 -
Min
4.0 0.45 0.45 -0.6 -0.6 0.9 0.4 0.85 0 0.35 0.4 0.4 0.4 0.9 0.9 0.4 0.4 tCLmin or tCHmin tHP-0.4
Min
5.0 0.45 0.45 -0.7 -0.7 0.9 0.4 0.8 0 0.3 0.4 0.4 0.4 1.0 1.0 0.45 0.45 tCLmin or tCHmin tHP-0.45
Max
10 0.55 0.55 0.7 0.7 0.45 1.1 0.6 1.2 0.6 0.6 0.6 -
Unit
ns ns ns tCK tCK ns ns ns tCK tCK tCK ns tCK tCK tCK tCK ns ns ns ns ns ns
Note
tCK tCH tCL tDQSCK tAC tDQSQ tRPRE tRPST tDQSS tWPRES tWPREH tWPST tDQSH tDQSL tIS tIH tDS tDH tHP tQH
1
1 1
Note 1 : - The JEDEC DDR specification currently defines the output data valid window(tDV) as the time period when the data strobe and all data associated with that data strobe are coincidentally valid. - The previously used definition of tDV(=0.35tCK) artificially penalizes system timing budgets by assuming the worst case output vaild window even then the clock duty cycle applied to the device is better than 45/55% - A new AC timing term, tQH which stands for data output hold time from DQS is difined to account for clock duty cycle variation and replaces tDV - tQHmin = tHP-X where . tHP=Minimum half clock period for any given cycle and is defined by clock high or clock low time(tCH,tCL) . X=A frequency dependent timing allowance account for tDQSQmax
- 14 -
Rev. 1.2 (Jan. 2004)
K4D261638F
AC CHARACTERISTICS (I - 1)
Parameter
Row cycle time Refresh row cycle time Row active time RAS to CAS delay for Read RAS to CAS delay for Write Row precharge time Row active to Row active Last data in to Row precharge @Normal Precharge Last data in to Row precharge @Auto Precharge Last data in to Read command Col. address to Col. address Mode register set cycle time Auto precharge write recovery + Precharge Exit self refresh to read command Power down exit time Refresh interval time
128M GDDR SDRAM
-25 Min
18 19 13 6 4 5 4 4 4 3 1 2 9 200 3tCK +tIS 7.8
Symbol
tRC tRFC tRAS tRCDRD tRCDWR tRP tRRD tWR tWR_A tCDLR tCCD tMRD tDAL tXSR tPDEX tREF
-2A Max
100K -
-33 Max
100K -
Min
16 17 11 5 3 5 3 4 4 3 1 2 9 200 3tCK +tIS 7.8
Min
16 17 11 5 3 5 3 4 4 3 1 2 9 200 3tCK +tIS 7.8
Max
100K -
Unit
tCK tCK tCK tCK tCK tCK tCK tCK tCK tCK tCK tCK tCK tCK ns us
Note
1 1 1
Note : 1. For normal write operation, even numbers of Din are to be written inside DRAM
AC CHARACTERISTICS (II - 1)
K4D261638F-TC25 Frequency Cas Latency 400MHz (2.5ns) 5 350MHz ( 2.86ns ) 4 300MHz ( 3.3ns ) 4 275MHz ( 3.6ns ) 4 250MHz ( 4.0ns ) 3 200MHz ( 5.0ns ) 3 tRC 18 16 16 16 13 12 tRFC 19 17 17 17 15 14 tRAS 13 11 11 11 9 8 tRCDRD tRCDWR 6 4 5 3 5 3 4 2 4 2 4 2 tRP 5 5 5 5 4 4 tRRD 4 3 3 3 3 3
(Unit : Number of Clock)
tDAL 9 9 9 9 7 7
Unit
tCK tCK tCK tCK tCK tCK
K4D261638F-TC2A Frequency Cas Latency 350MHz ( 2.86ns ) 4 300MHz ( 3.3ns ) 4 275MHz ( 3.6ns ) 4 250MHz ( 4.0ns ) 3 200MHz ( 5.0ns ) 3
tRC 16 16 16 13 12
tRFC 17 17 17 15 14
tRAS 11 11 11 9 8
tRCDRD tRCDWR 5 3 5 3 4 2 4 2 4 2
tRP 5 5 5 4 4
tRRD 3 3 3 3 3
tDAL 9 9 9 7 7
Unit
tCK tCK tCK tCK tCK
K4D261638F-TC33 Frequency Cas Latency 300MHz ( 3.3ns ) 4 275MHz ( 3.6ns ) 4 250MHz ( 4.0ns ) 3 200MHz ( 5.0ns ) 3
tRC 16 16 13 12
tRFC 17 17 15 14
tRAS 11 11 9 8
tRCDRD tRCDWR 5 3 4 2 4 2 4 2
tRP 5 5 4 4
tRRD 3 3 3 3
tDAL 9 9 7 7
Unit
tCK tCK tCK tCK
- 15 -
Rev. 1.2 (Jan. 2004)
K4D261638F
AC CHARACTERISTICS (I - 2)
Parameter
Row cycle time Refresh row cycle time Row active time RAS to CAS delay for Read RAS to CAS delay for Write Row precharge time Row active to Row active Last data in to Row precharge @Normal Precharge Last data in to Row precharge @Auto Precharge Last data in to Read command Col. address to Col. address Mode register set cycle time Auto precharge write recovery + Precharge Exit self refresh to read command Power down exit time Refresh interval time
128M GDDR SDRAM
-36 Min
16 17 11 4 2 5 3 4 4 2 1 2 9 200 3tCK +tIS 7.8
Symbol
tRC tRFC tRAS tRCDRD tRCDWR tRP tRRD tWR tWR_A tCDLR tCCD tMRD tDAL tXSR tPDEX tREF
-40 Max
100K -
-50 Max
100K -
Min
13 15 9 4 2 4 3 3 3 2 1 2 7 200 3tCK +tIS 7.8
Min
12 14 8 4 2 4 3 3 3 2 1 2 7 200 3tCK +tIS 7.8
Max
100K -
Unit
tCK tCK tCK tCK tCK tCK tCK tCK tCK tCK tCK tCK tCK tCK ns us
Note
1 1 1
Note : 1. For normal write operation, even numbers of Din are to be written inside DRAM
AC CHARACTERISTICS (II - 2)
K4D261638F-TC36 Frequency Cas Latency 275MHz ( 3.6ns ) 4 250MHz ( 4.0ns ) 3 200MHz ( 5.0ns ) 3 tRC 16 13 12 tRFC 17 15 14 tRAS 11 9 8 tRCDRD tRCDWR 4 2 4 2 4 2 tRP 5 4 4 tRRD 3 3 3
(Unit : Number of Clock)
tDAL 9 7 7
Unit
tCK tCK tCK
K4D261638F-TC40 Frequency Cas Latency 250MHz ( 4.0ns ) 3 200MHz ( 5.0ns ) 3
tRC 13 12
tRFC 15 14
tRAS 9 8
tRCDRD tRCDWR 4 2 4 2
tRP 4 4
tRRD 3 3
tDAL 7 7
Unit
tCK tCK
K4D261638F-TC50 Frequency Cas Latency 200MHz ( 5.0ns ) 3
tRC 12
tRFC 14
tRAS 8
tRCDRD tRCDWR 4 2
tRP 4
tRRD 3
tDAL 7
Unit
tCK
- 16 -
Rev. 1.2 (Jan. 2004)
K4D261638F
Simplified Timing @ BL=4
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
128M GDDR SDRAM
16
17
18
19
20
21
22
CK, CK
BA[1:0] BAa
BAa
BAa
BAa
BAa
BAb
BAb
A8/AP
Ra
Ra
Rb
ADDR Ra (A0~A7 ,A9~A11) WE
Ca
Ra
Ca
Rb
Cb
DQS
DQ
Da0 Da1 Da2 Da3
Da0 Da1 Da2 Da3
Db0 Db1 Db2 Db3
DM
COM
ACT_A
WR_A
PRECH
ACT_A
WR_A
ACT_B
WR_B
tRCD tRAS tRC
tRP tRRD
Normal Write Burst (@ BL=4)
Multi Bank Interleaving Write Burst (@ BL=4)
- 17 -
Rev. 1.2 (Jan. 2004)
K4D261638F
PACKAGE DIMENSIONS (66pin TSOP-II)
128M GDDR SDRAM
Units : Millimeters
(0.80) (0.50) (10x) (10x) 0.125 +0.075 -0.035 (0.50)
(R
(R 0 .2 5)
#66
#34
10.160.10
(1.50)
#1 (1.50)
#33
0.6650.05
0.2100.05
(0.80)
)
( 4x
15 )
0.05 MIN
0.
(0.71)
0.65TYP 0.650.08
0.300.08 (10x)
0.10 MAX [ 0.075 MAX ]
NOTE 1. ( ) IS REFERENCE 2. [ ] IS ASS'Y OUT QUALITY
(R
0x~8x
- 18 -
Rev. 1.2 (Jan. 2004)
0.
.1 5
0.25TYP
25 )
(R 0
(10x)
1.20MAX
22.220.10
1.000.10
0.45~0.75
)
11.760.20
(10.76)

▲Up To Search▲

Price & Availability of K4D261638F-TC33

	To Download K4D261638F-TC33 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .